Max2play and Spotify connect, picking up the gauntlet.

In a previous post, I discussed a plugin for Volumio to add Spotify connect ability to this headless audio-player OS.  I also pointed out that the competing OS, Max2play did not seem interested in incorporating this feature in their OS. A missed chance in my view, as there was a clear appetite for it if you checked the feature requests on their forum.

But they clearly took up the gauntlet, and after perfecting their plugin infrastructure and suggesting to the user community they could create a Spotify connect plugin, they came with such a plugin themselves.  It is still a beta version, with still some stability issues but if it is running, it works as it should.  This plugin has some prerequisites: It will only work if you’re a Max2play premium user (€9,99/year) and a Spotify premium user. In this sense, Volumio with the Balbuze plugin is still the cheapest solution.

Installation is quite straightforward, but also a bit more hassle than Volumio, especially when you are also using also other audio-players such as Squeezelite on Max2play. You can find my video tutorial and demonstration of the functionality below. As already said there are some stability issues. After some time the device Max2play with the Spotify connect plugin installed and running disappears from the list of available devices in the Spotify App. Stopping and restarting the instance of the plug-in will deal with this, but this should not be needed.

This is the link to download the plugin.

Retro tech: The Philips EL3515A

So far my blog and video’s has been about DIY tech stuff with a focus on audio. This time we stay in the realm of audio but go back time. Way back even before even I was born, because I would like to show you an old audio device that I saved from the skip somewhere in the 1990’s but was produced in the late fifties early sixties. It even still works (sort of). It’s an old table-top reel to reel tape recorder made by the technology pride of the Netherlands: Philips, more specifically the EL3515A model. This EL series of reel to reel tape recorders have been produced by Philips from 1957 onwards to 1968. But this EL3515A is an early model. The “A” indicates that it is a more luxurious version of the basic EL3515, with a wooden case covered with fake leather instead of a plastic case. It is pre-transistor device and its electronics is still based on radio tubes. One of the tubes is used for the “magic eye” which is in the big stop button, which lights up green when the device is on and should show the recording level. This is one of the first models with such a “magic eye”. The whole package comes in the form of a carrying case that is 370 mm wide,  160mm high and 320 mm deep.

The power cable and a separate mono microphone can be tucked away in a small compartment on the right side of the case with a removable lid. The whole thing has a hefty weight of around 8 kg, mainly because all the electronics and moving part are mounted in a cast-iron frame that resides in the wooden case. Because of this, I would not call it a mobile device. It runs off AC power switchable between 110, 127, 220 and 245 Volts. It is a mono device with around 2-2.5 Watts output. When you remove the plastic cover, you can see that it uses 9 to 13 inch tape reels. It plays and records two mono tracks (two sides) running at a speed of 9.5 cm/s.

After plugging in the power socket, you can switch it on by turning the left volume button. The whole thing directly springs to life with the hum of the drive motors, but playback can only be heard after a short warm-up until the “magic eye” is at its full intensity.  It is very basic machine, the extreme left and right buttons are for winding back and forth, then you have on the left, a pause button, on the right the play button and the big button in the middle with the “magic eye” is the stop button.  Between the two reels there is also a counter present, but this is broken on this machine. The turning nobs on the extreme left and right are on/off and volume left and the recording level on the right. The smaller nobs next to them are tone adjustment on the left and the red recording button on the right.

The “magic eye” lighting up in the stop button

When I rescued it from the skip somewhere in the 1990’s, it still worked fine and I used it as a novelty when my little nieces and nephews were visiting to record their voices and playing them back to them. That was always a lot of fun. Now it seems that the amplifier part of the device has deteriorated, playback and recording levels are low. It first off all would need a thoughrough cleaning. As it is now standing in storage, I am thinking to sell it off. Its seems that there are still some enthusiast out there who collect these things or scavenge them for the radio tubes. These tubes seem then to find their way into all kinds of DIY projects. When researching this device for this blog and my youtube video. I also came across an advertisement from the Leidsche courant from 1959 with prices for the EL3515, EL3515A and the more advanced EL3538. The EL3515A was priced at 398 Dutch guilders in 1959, which translates in a value of € 1 219.42 in todays money (Calculated with the tool here.), but I think I will make my asking price as a serious lot lower! If you want to see the EL3515A in action please watch my youtube video below.

The EL3515A in an Dutch advertisment from 1959

Volumio and Spotify Connect, Max2play bites the dust?

In previous posts I already talked about all these different headless audioplayer operating systems there are for small single board computers such as the Raspberry Pies (eg. Volumio and Max2Play). I also discussed that I am a Spotify user and love the Spotify Connect feature and the multiroom speaker possibility it brings. But the two audioplayer OSes that I am current testing did not support Spotify Connect so far, so I am currently resorting to a multiroom setup using Max2Play, Logitech Media Server (LMS) and the “triode” Spotify plugin to control several devices (RPis with Squeezeplayer software/Squeezebox duet receiver) for audio playback. It works, but the look and feel of LMS is very dated, so I am still on the lookout for improvement and I am not alone. The requested features section of the user forums of both Volumio and Max2Play show major interest in Spotify Connect. However the developer(s) of Max2Play does not seem to warm-up to this feature, while it trumps to be the multiroom audio centered OS. A missed chance in my view. In the meanwhile, Volumio has beaten Max2Play to the punch via support of third party plugins and the coding work available at Github of user “Balbuze” which seem to be based on previous work of “Fornoth” and “Plietar”. I am planning to test Balbuze’s Spotify Connect plugin “Volspotconnect” in Volumio shortly on my Pi Zero that currently runs Max2play. The plugin is specific for ARM6 and ARM7  chip based computers such the Rasberry Pi’s, so if you are running Volumio on a Intel machine, bad luck for now. It is a basic plugin that just makes your Volumio device show up as a Spotify Connect device. It has no connection with the Volumio interface yet, so no control via this interface or cover-art. This is no problem as you would rather use the Spotify software or app to control playback. It is clearly a work in progress. I also thought that you also needed a Spotify app developers key, which your can request here. However commenter Wim, indicated that this key is already present in the zip file provided by Balubuze. That makes it even simpler,  I hope to have time soon to get this up and running. This also seems a good topic for a Youtube tutorial so stay tuned!

Balbuze’s avatar on Github

 

 

Yeah, it works! See the tutorial here:

 

 

 

 

Setting up a USB Touchscreen to control your Raspberry Pi audioplayer

In an previous post, I discussed that I have been using the Logitech Squeezebox Duet and Logitech media server (LMS) software, to be able to play my mp3 collection and stream audio from Spotify. But the iPod shaped Duet controller, over 7 years old, got some issues charging its battery. I am hoping to be able to fix it, but in the meanwhile I wanted a bit of a replacement, to control audio playback, without using for example, the “Squeezer” app on my android phone.

The Logitech Squeezbox Duet controller.

Before I bought the Squeezebox duet somewhere in 2009, I had been experimenting with a touchscreen based solution in combination Asus eeebox mini PC, but wasn’t really satisfied. Then came the Squeezebox duet along and I replaced the touchscreen setup for it. However, I kept the LG Flatron L1510SF 15-inch touchscreen. Now in 2016 one of the best community supported mini PCs must be the Raspberry Pi. I have also been playing with it to make both video and audio-player devices. There is also already a whole range of supported small touchscreens, which connect via the GPIO header or Display header, but using screens with HDMI, DVI, or VGA input and USB for the touch-control seems not so common. But when my Squeezebox Duet controller got issues charging, I was thinking why not pair my old 15-inch touchscreen with a Raspberry Pi running LMS?

Setting up Logitech Media Server (LMS)

Setting up a Raspberry Pi with LMS is very simple when you use the Max2Play audioplayer OS. Just download the SD image from the Max2play website, write it to the SD card with a tool like win32diskimager. Insert the SD in the Rpi, connect the Rpi to you network using an ethernet cable and power it up. You now can enter the setup of Max2play on you Rpi, by typing the URL: max2play/ in your browser. In the setup interface you can select to install LMS and the Squeezerplayer playback software onto you Raspberry Pi automatically. In this way you have a headless audio server device, which can playback songs locally or on other squeezebox devices on your network. You can control it via an app like Squeezer on android or by logging into the LMS server web-interface on your laptop or PC.

Jivelite, the touchscreen interface for LMS

The LG Flatron L1510SF USB controlled touchscreen.

In my case, I wanted to use a local touchscreen display to control Rpi with LMS. For this, you have to do some extra work. First of all, you need to connect the screen and also for setup purposes, a keyboard and mouse. Secondly you need to install the JiveLite Squeezebox interface software via the Max2play setup. This is a Max2Play premium feature which costs you a license fee of €9,99 per year. It is possible to setup LMS and Jivelite without Max2Play, but not as effortless as provided by the setup interface of Max2play. The JiveLite setup in Max2Play lets you also select several JiveLite interface skins, but these are tailored to the smaller Raspberry Pi specific touchscreens and needed some modification to get a fitting layout for the 1024×768 resolution of my LG touchscreen. But more about that later.

Calibrating your USB touchscreen

Now we first need to get the USB touchscreen working with the Raspberry pi. When researching how to do this, I came across this article (in Dutch). Which describes the process for the exact same screen as I am using. First of all, you need to install xinput-calibrator. You best do this locally on your Rpi using the attached mouse and keyboard by opening a terminal window and typing sudo apt-get install -y xinput-calibrator. You now have to run xinput-calibrator by typing xinput-calibrator. This will open a window for calibration. You can follow the instructions for calibration and use a stylus for best precision. This will result in an output window with calibration parameters that need to be put into the /etc/X11/xorg.conf.d/99-calibration.conf file. I did this with the parameters I recorded but run into problems. The LXDE gui would not show after a reboot. So in the end, I just used the exact same settings as described in the article with the exact same LG touch screen. That did the trick, the touchscreen is working fine.

Making the Joggler skin fit your resolution

Now I wanted the have a JiveLite skin that was a good fit with the resolution of the screen. The Joggler skin, came nearest to what I wanted but needed adjustment to fill the whole screen. For this you need to edit the code of skin file: /opt/jivelite/jivelite/share/jive/applets/JogglerSkin/JogglerSkinApplet.lua

And edit line 259 so it reads:
Framework:setVideoMode(1024, 768, 0, false) where 1024 and 768 reflect the resolution and aspect-ratio of the screen.

When you want the spectrum visualizer of Jivelite to show correctly (Only visible when playing audio locally on the LMS machine). You also need to edit the following section in the JogglerSkinApplet.lua file. The values to edit are shown in bold

-- Visualizer: Spectrum Visualizer
s.nowplaying_spectrum_text = _uses(s.nowplaying_visualizer_common, {
npvisu = {
hidden = 0,
position = LAYOUT_NONE,
x = 0,
y = 2 * TITLE_HEIGHT + 4,
w = 1024,
h = 566 - (2 * TITLE_HEIGHT + 4 + 45),
border = { 0, 0, 0, 0 },
padding = { 0, 0, 0, 0 },

spectrum = {
position = LAYOUT_NONE,
x = 0,
y = 2 * TITLE_HEIGHT + 4,
w = 1024,
h = 566 - (2 * TITLE_HEIGHT + 4 + 45),
border = { 0, 0, 0, 0 },
padding = { 0, 0, 0, 0 },

After a restart of the Jivelite GUI, or reboot of the system, the layout should have a good fit with the resolution of the screen. Some buttons may still not have the most perfect scaling, but it is all functional. I however will, keep an eye open for a more perfected 1024×768 skin for JiveLite. If you a reading this and have one or knows one, please let me know.

Finally

One small thing is still bothering me and this is the visible mouse cursor. Max2Plays add-on, specific for the smaller Raspberry Pi touchscreens, has a very handy checkbox to make the mouse pointer on a touchscreen invisible. But as my touchscreen is not supported by this add-on, I cannot use it. Any suggestions to make the mouse pointer disappear are also very welcome. To get a better impression of how it works and what it looks like I recommend you to watch my youtube video about it, here below.

How I still got to use Spotify on my WiFi speaker

In my previous post, I discussed the problem with the Medion P69055 WiFi multiroom speaker and Spotify connect. It could and should support Spotify connect, but most probably lacks a firmware update to enable this feature. A big let down by Medion, but how to solve this? In the end, I opted just to use the line-in of the speaker and connect some “low-cost” device that supports Spotify. In this post, I will discuss three different devices to achieve this.

1. A netbook/laptop with Volumio and the Spotify plugin.

I already showed in my first post and youtube video, how to turn any old intel based laptop or netbook into a headless audio player that can be controlled by a webinterface on your smartphone or other PC, while closed and hidden from sight. In this case you just plug in this device into the line in of the speaker and voila. Pro: If you have an old laptop or netbook available and an SD card then you get it working without extra costs. Con: Even a small netbook is still a bulky device which is not easy to hide.

2. Chromecast Audio

With a price-tag of below €40, the Chromecast audio is a cheap and simple device to get Spotify on any speaker or audio system. It is also conveniently small. It gets powered via an micro usb port and with an extra accessory, you can also use an SPIF digital audio cable to connect the cast to your audio system. Setup is simple and straightforward to let it connect to your WiFi router. You can also set it up to allow your friends to connect to it with their android smartphone, so you can have an evening of music sharing.

The Chromcast audio is android phone centered and is not visible for other devices with the Spotify software until you activate it using the Spotify app on your android smartphone. If you use the Chrome browser you can circumvent this by using the Chromecast extension in combination with the Spotify web player. Pro’s: Cheap, small, easy to setup. Con: Really android phone centered.

Chromecast audio

3. DIY project: A Raspberry Pi zero with a DAC.

This last solution is a completely other beast. It’s not the cheapest solution and requires SOLDERING. So let’s list what you need:

  1. A Raspberry Pi zero. This is the most minimalistic, smallest and cheapest of the Raspberry Pies. Because of its popularity, it is also hard to get and the three webshops where you can get them only allow you to order one per customer. There is also this neat little website to see which web shops have them in stock: whereismypizero.com. A single Pi zero costs about €5, but most shops offer them in project kits between €15 and €35.
  2. The Pimoroni pHAT DAC. This is a Pi zero sized digital analog converter board, which uses the same chipset as the much more expensive HiFi-berry full-size boards. A single pHAT DAC board is available for prices between €14 and €20.
  3. GPIO headers. The Pi zero and pHAT DAC only have holes and no GPIO headers, so you have to solder these on yourself. This allows for more freedom to connect the pHAT DAC to Pi zero in different configurations depending on the size of your case. I just soldered a strip of male GPIO pins on the zero and a female header on the pHAT DAC board. You only need 5 pins to make the connection between the Pi zero and pHAT DAC working. I however, used the full 20 pins to make the connection also mechanically stronger.
  4. A Rasberry Pi compatible Wifi dongle, with a micro USB connector or a normal one and a micro to full-size USB adapter.  This should set you back for between €5 and €10 euro depending on the shop. Yes, the Pi zero has no onboard Wifi like the Raspberry Pi 3, which is a pity.
  5. A class 10 micro-SD card of 8 Gb or more, to install an OS and audio player software.
  6. A nice case to put it all in. I opted for this small polycarbonate case I found on amazon. It needs some adaptation to allow access to the 3.5 mm jack of the pHAT DAC and it is a snug fit with the pHAT DAC on top of the Pi-zero, but it is nice full enclosure with access to all ports and the micro SD card slot.
  7.  A USB 5V 2 A power adapter to power the Pi zero.
  8. Optional: a USB hub with Ethernet connector, for the initial setup op the audio software on the Pi zero before switching to Wifi. The software used, also allows initial setup using WPS, but I found that to be a bit of plug and pray feature. With a network connection via a cable, your sure it will work.

    The Pimoroni Wireless Audio Kit.

In the end, I opted for the Pimoroni pHAT DAC Wireless audio kit which consists of a Raspberry Pi zero, the Pimoroni pHAT DAC, the needed GPIO headers, a WiFi dongle with adapter and A 3.5 mm Jack cable male to male. It also includes some parts I did not use like the micro HDMI to HDMI adapter, the RCA out adapter that can be soldered onto pHAT DAC board and USB to micro USB adapter. But with a price tag at the time of around €30 euro it is still a good deal for the parts I needed. I also bought the USB 5V 2A powersupply for around €6 euro and the USB hub for just below €10. The small polycarbonate case set me back €6. So round and about 52 euro without the SD card, so let’s say €60 with.

The Pi-zero/pHAT DAC in the case. The slit to fit the top of the case over the pHAT DAC board is not very pleasing to the eye but functional.

So on to the assembly of this device, which starts with soldering the GPIO headers on to the Pi-zero and pHAT DAC board. For any instructions on that just look on YouTube, like this video, this or this one. I myself used some blue-tac type putty to stabilize the PCBs on my table to do the soldering. With the GPIO pins and female header attached you can now connect the pHAT DAC board to the Pi-zero. I then modified the top lid of the polycarbonate case with a cutter knife and sanding stick to make a slit for jack line-out socket of the pHAT DAC. It came out to be, let’s say more functional than esthetical. But to my pity, I do not have a Dremel rotary tool to my disposal. It has to be a slit, as the top lid has to slide over the pHAT DAC board with no space to spare and this socket sticks out. With this modification done, the case can be closed. With this, most of the assembly work is already done. You can also find more detailed instruction on how to assemble a Pi zero with pHAT DAC combo elsewhere on the internet, like for example this one.

The next step is to prepare your SD card with an appropriate audio player dedicated OS. As described earlier, there is choice, such as  Volumio, Mood audio and Rune audio. For this project my choice was Max2play, which is really multiroom centered and supports Logitech Media Server (LMS) software using Squeezeplayer. I was already acquainted with this system, having a Logitech Squeezebox Duet in use and LMS, with the needed Spotify plugins, running on a local Linux machine. LMS has also the nice feature that you can synchronize playback of your speakers via wifi. Which is ideal for parties when you want the same background music everywhere around the house.

Setup is straightforward: Download the Max2play disc-image (in this case the image with Hifi-berry support) and write it to the SD card. I then inserted the SD card in the assembled Pi-zero, attached the USB hub to the USB peripheral port of the Pi-zero with the Wifi dongle and an ethernet cable inserted, the last of which in turn was connected to my router. I then powered up the Pi-zero using the 5V 2A USB PSU. On another computer I entered the URL: max2play/ and voila the Max2play setup interface was loaded. In this interface I set my Wifi SSID and password, activated Squeezeplayer and indicated that I wanted to use a Hifi-Berry (PI A/B) as audio output to activate the line-out on the pHAT DAC. This initial setup is also explained in this Max2play tutorial video. Then I initiated a shutdown, removed the USB hub and connect the Wifi Dongle directly to the Pi-zero. I could now connect the Pi-zero to the Medion P69055 speaker, select in-line, power up the Pi-zero and voila: A wifi enabled speaker with Spotify that I can control using my smartphone and more importantly with the Logitech Squeezebox duet controller I already used for my HiFi system in the living room. But after a couple of months, my trusted duet controller got battery charging issues, but that’s for another time.

The pro’s: More flexible and fun solution and great sound of a good quality DAC. The con’s: More expensive than the Chromecast, and you have to assemble it yourself. But for me that is half the fun!

Conclusion

So these are some solutions to the issue of no Spotify on the Medion P69055, but of course also applicable to any audio system with a line-in. The “low cost” aspect is rather relative of course, only the old disused laptop with Volumio is really low cost. The Chromecast audio and Pi-zero are 40 and 60 euro respectively and that to fix a speaker which cost me just about €100, bummer! But okay, now it works to my satisfaction so I am fine in the end. You may say that technically non of the solutions are genuinely Spotify-connect solutions. Yes that’s true, but all solutions allow you to play music using your Spotify premium account, they are just not using the Spotify Connect protocol. The Spotify Connect protocol is currently dissected by several enthusiasts, so I expect that this feature will become available for the Raspberry Pi zero in any shape or form. I will be keeping an eye on that. I like the Raspberry Pi zero pHAT DAC combination best as it is the more flexible solution in terms tweakablity. Do you want Apple Airplay or use Google Music instead of Spotify? The Rasberry Pi with Max2play has that flexibility. One thing to keep in mind is to use a good PSU for the Raspberry Pi zero pHAT DAC. Digital/Analog converters are very sensitive to power fluctuation and using a botched PSU may introduce interference. The Medion P65099 has for example a USB charging port, but powering the Pi zero pHAT DAC combination, but also the Chromecast via this port, resulted in background static. Real audiophiles use PSUs with linear power outs, to have the best sound quality, but I this case this is a bit overkill.

There are also other Chromecast audio like devices that are genuine Spotify Connect devices such as the Fon Gramofon and Rocki. Both start at a €65 price tag and especially the Rocki, a former Kickstarter project got bad reviews with difficult setup, bad customer support and melting batteries. The Gramofon I still find quite intriguing as it also uses the same Quallcomm Allplay technology that should allow the Medion P65099 speaker to use Spotify Connect. However with reviews questioning the sound quality of the Gramofon and the price tag of €65 make me hesitant.

The Fon Gramofon

Spotify connect ready or not?

medion-life-p69055-md-83867-865x433

Medion Life P69055 (MD 83867)

A couple of years back, I bought a wifi-speaker which seemed to have everything for it. It sounds good, it looks good (reddot design award), easy to setup, what’s not to like? I bought this device as a replacement for my radio in my kitchen with idea that I still could listen to webradio but also could stream music using Spotify connect. Yeah, but then your device should be Spotify connect ready, isn’t it? True, there are wifi speakers out there that do not support Spotify connect. But this was not a real impuls buy, and I informed myself well about this device technical background and concluded that it supported Spotify connect. I was however greatly mislead.

The Medion Life P69055 (MD86867)
screenshot_20161022-112920

The Medion app even lists Spotify?!

The device I am talking about is the Medion Life P69055 (MD 83867), that I bought just under a €100 at Aldi. Some of you will say, aha Medion and Aldi, whomever would buy an appliance there, its a supermarket! However in my experience and I have owned several Medion Akoya PCs, is that Medion is not great, but far from bad. But still the P69055 seemed to have everything for it. It uses Quallcomm’s Allplay technology which according this press-release by Quallcomm is Spotify connect certified. The Medion P69055 is also featured on the Spotifygear.com website, that lists available Spotify connect devices and as far as I can tell this site is endorsed by Spotify. When I got the device, installed it and started using the Smartphone app to control it, it has a separate menu for streaming services that lists Spotify next to Doubletwist and Raphsody. However when you select Spotify it only starts the Spotify app. In the Spotify app any available Spotify connect device should be seen at the bottom of the screen, but the P69055 never shows up. First I thought this could be due to some port-forwarding issues on my router, but I could put that to bed, after tests with other devices. So finally I called the Medion helpdesk.

Helpdesk BS

I really loath these “non skilled” helpdesks, which only seem to use scripted answers, that only help total nitwits. Sometimes I even seem to hear, that the person on the other side of the phone-line, actually does not understand what they are telling me. Generally, they never know how to deal with a bit more technical savvy person like me. So the advice was to put it in writing on their support page. So I did, added the evidence above to show that it should work and that it was even intended to do so, in view of their own Life-stream speaker control app. The answer I got was total BS, blaming Spotify for not supporting DLNA. A clear diversion of the issue to something outside of Medion’s influence, the oldest tactic in the book. Shame on you Medion!

Where is the firmware?

In the meanwhile I also posted the same question on a Spotify forum and there I got an answer that struck me as more valid. Yes, Quallcomm Allplay devices are Spotify connect certified, but may need a firmware update to work. So I was still positive that a firmware update would arrive and Spotify Connect would start working. The last update was somewhere in the last quarter of 2014, I believe, but no Spotify connect and no more firmware updates since. So I have given up hope that this will ever happen.

Conclusion

I do not know if this is, a can not or will not by Medion, but I can only conclude that the Medion P69055 (MD83867) does not, I repeat NOT support Spotify connect. If Spotify has something to do with the Spotifygear website, they also should remove the P69055 from the list as this is quite misleading. So did you return the device, you might ask? No. it was to late for that. However I thought of a DIY fix, which was an extra cost, but it does the trick. I will eleborate on that in a next post.

Streaming audio to your Hifi? Just use an old laptop.

I’m probably not the only one who has shelves full of CDs, folders with between 10 and 100 GB of MP3s and is now consuming his music mostly via streaming services like Spotify. The latter two clearly aimed to personal use initially, on a MP3 player, iPod or your smartphone and some headphones. So If you want to play music on you Hifi, you perhaps still revert to ordinary FM radio or a CD. In the meanwhile all kinds of solutions for playing MP3 on your HiFi have been developed. Tuners/Amplifiers with USB or network input and WiFi connections that support DLNA, so that MP3s in a folder on your computer or network storage can be played.

logitech_duet

Logitech Squeezbox Duet.

I myself purchased the Logitech Squeezebox Duet, for this purpose, back in 2009. This solution consists of two devices. The receiver box to connect to your HiFi set and the controller, a remote with an iPod-like jog button to go through the different menus. The two devices talk to each other using Wifi (or wired network connection in the case of the receiver) and a PC with your MP3 collection, running a special server-software. This set-up was at the start not a very easy configurable and stable solution.

However if you also want to use streaming services on your Hifi, you need to make another step. (In the case of the Squeezebox this was a small one, but I will perhaps cover this in another post.) You can of course connect your smartphone directly to your Hifi, but that is not very practical. You can invest again in new streaming ready devices. There are a lot of wifi and streaming enabled speakers available these days, with SONOS as maybe the best known but certainly not the cheapest example. However a lot of tweakers have come up with cheap and workable DIY alternatives.

raspberry_pi_3

Raspberry Pi revision 3.

Especially the arrival of the Raspberry Pi seems to have been a catalyst for all kinds of solutions to stream your audio in a simple way to your Hifi. For those who do not know: The Raspberry Pi is a relatively inexpensive mini-computer (~ € 35 without a housing) of credit card size. We now arrived at version 3 of this computer, that has a micro-SD card slot for the software and also an HDMI output, audio/video jack, 1 micro usb for power and further a LAN port, 4 full size USB ports, WiFi and Bluetooth. Furthermore, the Raspberry Pi has the so-called “general purpose input / output pins” or simply GPIO pins. These pins can be used to control all kinds of stuff. In the case of Hifi there are beautiful solutions such as high-quality digital to analogue audio converters boards, that give superior sound quality compared to the standard audio chip of the Raspberry. Examples of this are the Hifiberry range and Pomorino’s Phat DAC.

Nice pieces of hardware you might think, but what about the software? The Raspberry Pi has a fantastic community of tweakers who develop both hardware and software, mostly as open source, freeware. When it comes to so-called “standalone” or “headless” audio players, there is choice. There is Max2play, who also offers multi-room speakers support and three other packages, which have a shared history: Moode audio, Rune audio and Volumio. Max2play, Mood and Rune audio are all focused on just the Raspberry Pi and similar minicomputers, Volumio however, has two bonuses: Support for Intel computers, or in other words: Any old PC or Laptop may have lying around, and a Spotify plugin .

eeepc4g

The Asus eeePC 4G.

In my case I still had an early netbook lying around and I was wondering if Volumio would run or not, on such a underwhelming machine. I am talking about an ASUS EeePC 4G, see here for its specification. The existing 500 mb of RAM, I replaced for 1Gb. The internal storage of 4GB is also tiny, but we do not need it, in this case, as we run Volumio from a SD card. It should be possible to install Volumio on the internal storage, but this is (still) a bit cumbersome.

In itself, the installation is fairly straightforward and clearly explained on the Volumio website. I also made a YouTube video where I run through the required steps, which you can watch below.  First of all, you must download an SD disk image, the Intel (x86 / x64) version in this case, from the Volumio website. Then use a software tool like Win32imager or Rufus to write this image on an SD card of at least 4Gb and speed class 6. Generally it is advised to use a class 10 card, but I had only a class 6 SD around and it works well. Now it’s just a matter of booting from the SD card. This requires some modifications to the BIOS settings. After that, it takes some time for Volumio to get ready for its first use. After this lengthy initial start-up, reboots are going much quicker.

Volumio is primarily intended as a “headless” audio player, which means you control it via a web interface on your PC, laptop, tablet or smartphone. You can use this interface by entering the URL: /volumio.local or IP address of your Volumio machine in a webbrowser. The laptop has a screen so you can also control it using this. This is especially useful for the setup of you Wifi connection for the first time. I also noticed that the interface on the laptop itself was a lot slower than the webinterface on another PC or smartphone, which is striking. Via the (Web) interface, you can also configure other things such as the connection to your music folders and of course installing and setting up the Spotify plugin. You’ll need a Spotify Premium account for that. As you will see in the video, Volumio is working properly on this underwhelming mini laptop. So if you’ll be using a newer model,  there is no reason, for it to work as well.

The only minor thing I run into was, that for a true headless audio player, you would like to use it with the lid closed. You can then connect to your hifi and hide it. Unfortunately, many laptops go into a sleep mode if you close the lid and then the music stops. This is not convenient, but for this I have found a “hack” to solve this. Volumio is based on a Linux operating system and you can use the software tool PuTTY (Windows) to create a so-called SSH connection. You can than give commands to the Linux backend. In this way, you can disable all sleep and suspend modes and it will continu to play the music, when you close the lid. This is also shown in my Youtube video below. After logging in via SSH (Putty) using the IP Address of your Volumio machine with user: Volumio and password: Volumio. You should than enter the following command:

systemctl mask sleep.target suspend.target hibernate.target hybrid-sleep.target

Followed by pressing <Enter>. This will disable all sleep modes in your settings. In this case it is important to always keep your laptop plugged in, the battery will otherwise run out of juice a can damage your SD card.

Success!